Take Your 3D Printing to the Next Level with These Game-Changing Upgrades! - #Waliorit #ep4

In this video, we will learn how to transform an Ender 3 3D printer by upgrading it with a glass bed, metal extruder, and CR touch. We will also install Octoprint on a Raspberry Pi Zero and use gphoto2 for high-quality timelapses using the Octolapse plugin for Octoprint and a DSLR Camera. Additionally, we will configure VSCode to build Marlin firmware and use it to support the CR touch. Chapters: 00:00 Intro 00:11 Format the SD Card 00:27 Download and install Octoprint 01:06 Mount the Raspberry Pi Zero and its USB HUB HAT 01:43 Configure gphoto2 in Raspberry Pi Zero 02:59 Setup OctoPrint 03:32 Install and configure Octolapse with a DSLR 04:49 Add Automatique Cura Slicer Configuration for Octolapse 05:14 Ender 3 Glass Bed 05:30 Unboxing 05:40 Ender 3 Metal Extruder replacement 06:24 CR Touch Installation 07:29 Build Marlin firmware in VS Code 10:23 Flash Marlin and Configure Z Probe Offset 11:03 Design and print Raspberry Pi zero case 11:49 Mount Raspberry Pi case 12:38 Outro Resources: Raspberry Pi Case: https://thangs.com/designer/waliori/3d-model/Case%20for%20Raspberry%20zero%20and%20Usb%20Hub%20Hat%20and%20camera-837910?manualModelView=true&source=Recent Affiliate links (helps me with no extra cost for you, Thanks ??) 3d Printer: Amazon CA: https://amzn.to/3mZnfyK Amazon US: https://amzn.to/3AtRJfv Silent Board: Amazon CA: https://amzn.to/40AM9CD Amazon US: https://amzn.to/3AotgrI Combo I bought: CR Touch + Metal Extruder + Capricorn Bowden PTFE Tubing + ... Amazon CA: https://amzn.to/43YoGOE Amazon US: https://amzn.to/40zml9V Glass Bed: Amazon CA: https://amzn.to/3LrMy5V Amazon US: https://amzn.to/3n1tr9y Metal Extruder & Capricorn Bowden PTFE Tubing: Amazon CA: https://amzn.to/3L7v0KY Amazon US: https://amzn.to/3KZ4Da6 CR Touch: Amazon CA: https://amzn.to/3ox2A5s Amazon US: https://amzn.to/3V7Bk9V Raspberry camera: Amazon CA: https://amzn.to/3n3GcAg Raspberry USB HUB HAT: Amazon CA: https://amzn.to/3HaTfqs Amazon US: https://amzn.to/44bFJwS Details and steps: 1: Format the SD Card 2: Download,install and run Raspberry PI Imager https://www.raspberrypi.com/software/ a: Operating System = Other , 3D printing , OctopI b: Settings = enable ssh, set a password for the "pi" user, Enter Wifi SSID and password c: save and write 3: after inserting the SD Card in the Raspberry Pi and power it ON, wait a little bit and verify your WiFi router for the IP address of the Raspberry Pi, 4: Octoprint Setup Wizard is straight forward 5: Install Octolapse and Follow the excellent guide of FormerLurker in this page to configure it: https://github.com/FormerLurker/Octolapse/wiki/V0.4---Configuring-a-DSLR 6: configure your slicer following the guide corresponding to your slicer https://github.com/FormerLurker/Octolapse/wiki/V0.4---Automatic-Slicer-Configuration 7: Install VS Code extensions: a: https://marketplace.visualstudio.com/items?itemName=platformio.platformio-ide b: https://marketplace.visualstudio.com/items?itemName=MarlinFirmware.auto-build 8: Download Marlin firmware and its configuration from : https://marlinfw.org/meta/download/ 9: Extract Marlin firmware to a short path folder (example C drive) 10: extract content of your (printer-motherboard) from the configuration to the "Marlin" folder inside Marlin firmware previously extracted folder (overwrite) 11: Open VsCode from the Marlin firmware folder (not Marlin folder which is inside) and build for a first time 12: i followed @TeachingTech excellent guide for my configuration: - Configuration.h: * uncomment: define AUTO_BED_LEVELING_BILINEAR define Z_SAFE_HOMING define USE_PROBE_FOR_Z_HOMING define S_CURVE_ACCELERATION * comment: define Z_MIN_PROBES_USES_Z_MIN_ENDSTOP_PIN * for NOZZLE_TO_PROBE_OFFSET check the genius respone of HolidayWallaby here:https://www.reddit.com/r/ender3/comments/ks3afd/help_me_figure_out_probe_nozzle_to_probe_offsets/ - Configuration_adv.h: * uncomment: define BABYSTEP_ZPROBE_OFFSET define PROBE_OFFSET_WIZARD 13: build and copy the firmware to the SD card and flash it to the printer. 14: i followed @TeachingTech video for Z Probe Offset https://www.youtube.com/watch?v=fN_ndWvXGBQ #3Dprinting #Ender3 #DIY #upgrades #Octoprint #RaspberryPi #timelapse #Marlinfirmware #CRtouch #glassbed #metalextruder #VSCode #automatiquecura #DSLR #Octolapse #gphoto2 #tutorial #asmr #rainsounds #ep4 #waliorit